nodeset aborted with "Unable to find pxelinux.0 from syslinux" when neither
the copy under the tftp directory nor the one under XCATROOT existed. Only
legacy BIOS clients chain pxelinux and not every distribution still ships
syslinux, so a UEFI-only environment could not run nodeset at all.
Copy pxelinux.0 when it is available and warn, rather than fail, when it is not.
Recovered from the unmerged lenovobuild branch (4f0a5106), which skipped
silently; warn so the missing loader is still reported.
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
ddns.pm's DNS-update send has a 3-try retry loop, but it only retried on
NOTAUTH and -- on the final attempt -- the `next` fell out of the loop without
reporting failure. makedns then printed "Completed updating DNS records." and
"DNS setup is completed" even when the update was never accepted.
Two problems this causes:
- SERVFAIL was never retried. named routinely replies SERVFAIL transiently
right after a zone (re)load, before the zone is ready to accept dynamic
updates; the update succeeds a second or two later. This reliably breaks real
flat-cluster provisioning on el9/el10, where the test case's makedns -n runs
right after named reloads the zone with the new compute node.
- A persistent NOTAUTH/SERVFAIL (retries exhausted) was silently swallowed and
reported as success, so a genuinely failed DNS update looked like it worked.
Extract the batch send into send_ddns_update(), which retries NOTAUTH and
SERVFAIL (pausing on SERVFAIL), returns 0 only on NOERROR, and otherwise emits
the error and returns 1. Both batch-send sites now `return 1 if
send_ddns_update(...)`, so a real failure aborts add_or_delete_records instead
of falsely reporting success.
Signed-off-by: Daniel Hilst <392820+dhilst@users.noreply.github.com>
Modern x86-64 UEFI firmware (including OVMF and recent iPXE) reports DHCP
client architecture 00:07, but the xNBA network-boot conditionals only matched
00:09. A UEFI node would load xnba.efi, re-request with user-class xNBA and
arch 00:07, fail to match, and be handed xnba.efi again -- an endless boot
loop. Accept 00:07 alongside 00:09 in the xNBA UEFI branches of both the
network-level (addnet) and node-level (addnode) dhcpd statements.
Validated on an OVMF UEFI client: it progresses from xnba.efi to the .uefi
genesis config and boots, instead of looping on xnba.efi.
Recovered from the unmerged lenovobuild branch (5d697b5c, 86b0e12e).
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
The DNS-managed-networks check used my_ip_facing($net->{net}), which only
returns local addresses on the interface directly facing that network. A
nameserver that is a local address reachable via a different (routed)
interface was therefore treated as external, and the network was wrongly
dropped from ddns management.
Use thishostisnot(), which recognizes any local address regardless of the
interface, and keep the existing <xcatmaster> and site-nameserver special
cases.
Recovered from the unmerged lenovobuild branch (original 3c343f83), adapted
to preserve those special cases: lab validation showed the original replaced
them wholesale, which would exclude any network whose nameserver is the
literal <xcatmaster> token (thishostisnot('<xcatmaster>') is true).
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
nodech's ^= operator removed only a single literal value, so
"nodech n1 groups^=a,b" tried to strip the combined string "a,b" and left the
individual groups in place. Split the value on commas and remove each piece.
Recovered from the unmerged lenovobuild branch (original 95c78b33).
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
nodech's ,= operator appended the whole right-hand side as one value, so
"nodech n1 groups,=a,b" added the literal "a,b" and its duplicate check only
compared against that combined string. Split the value on commas and add each
piece individually, skipping any already present.
Recovered from the unmerged lenovobuild branch (original 086b0c0d).
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
`ip -6 route` output for ECMP/multipath routes carries `nexthop` continuation
lines, and a `default` route has no network prefix. donets() treated both as
networks and added bogus entries to the networks table. Skip them alongside
the existing link-local/unreachable/via/lo filtering.
Recovered from the unmerged lenovobuild branch (original 7094ba0c).
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
donets() only skips the exact address 'fe80::/64' when scanning routes, so a
link-local route with any other prefix (e.g. a longer fe80:: subnet) is added
to the networks table as a bogus network. Match any fe80:: prefix instead of
the single literal value.
Recovered from the unmerged lenovobuild branch (original 8b79cf85).
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
getzonesfornet() derives the number of reverse-zone nibbles as
$nibbs = $maskbits / 4, then decrements it once per hex nibble of the network
prefix. For a sub-nibble (not 4-bit-aligned) IPv6 mask $nibbs can go negative
before the padding loop, and `while ($nibbs)` then never terminates: it keeps
decrementing past zero while appending "0." to $rev, spinning forever and
growing the string until the process is killed.
Make the padding loop `while ($nibbs > 0)` so it can never run away, and
return early only when $nibbs is genuinely negative. $nibbs == 0 is the normal
nibble-aligned case (e.g. a /64) and must still emit its reverse zone.
Recovered from the unmerged lenovobuild branch (original 0e070cd2). The
original guarded with `$nibbs < 1`, which also dropped the valid $nibbs == 0
case and left standard /64 subnets with no reverse zone; corrected to
`$nibbs < 0` after lab validation on a real provisioning cluster.
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
mknb writes the compressed genesis filesystem by streaming cpio output
straight onto the final path in $tftpdir/xcat (genesis.fs.$arch.lzma or .gz).
When two mknb/nodeset runs target a shared $tftpdir at once, one run reads or
overwrites the other's half-written image, producing a corrupt genesis.fs and
failed netboots.
Write each image to a uniquely-suffixed temporary file
(xCAT::Utils::genpassword(24)) and File::Copy::move() it into place. move()
within the same directory is a rename, so the final path only ever appears
complete. Both modules are already imported by mknb.pm.
Recovered from the unmerged lenovobuild branch (originals c651e7b8 and its
fix da0723f2, which switched the suffix to genpassword after the first
attempt only produced a single character). master lacks the branch's xz
path, so only the lzma and gzip paths are adjusted here.
Co-authored-by: Jarrod Johnson <10814490+jjohnson42@users.noreply.github.com>
build_xmldesc only recognised cpumodel "ppc64" (big-endian) when deciding to set
<os type arch='ppc64' machine='pseries'>, but ppc64le hosts report cpumodel
"ppc64le" (virNodeGetInfo model). A guest on a ppc64le hypervisor was therefore
emitted as an x86-style domain -- no machine type and with pae/acpi/apic -- and
libvirt rejected it: "machine type 'pseries-*' does not support ACPI".
Recognise "ppc64le" alongside "ppc64" for the arch/machine block, and omit the
x86-only pae/acpi/apic features on both. Little- and big-endian pseries guests
both use libvirt <os> arch "ppc64".
Signed-off-by: Daniel Hilst <392820+dhilst@users.noreply.github.com>
When all addkcmdline options have R:: prefix (persistent options for
the installed OS), the volatile check in xnba.pm and pxe.pm would fail
because volatile was undefined. This left the original R::-prefixed
string in the netboot config instead of stripping it.
The fix ensures we always use the volatile portion after calling
splitkcmdline, even if it's empty. Persistent (R::) options are
handled separately by Template.pm via PERSKCMDLINE for the installed
OS bootloader.
Fixes#7442
The activenics{"!remote!"} hash key is checked at line 1940 but never
set by any code path — neither the dhcpinterfaces parsing nor the
querynics discovery populates it. This causes the guard to always
evaluate true, hitting next and silently skipping every !remote!
network when dhcpinterfaces is defined in the site table or on a
service node.
Remove the dead check so remote networks are processed correctly.
The inner activenics{$netif} check (which uses the actual interface
name after stripping the !remote! prefix) is the correct guard and
is preserved.
Original analysis by lebonez in xcat2/xcat-core#7242.
Co-authored-by: Lebonez <25910791+lebonez@users.noreply.github.com>
Add a shared OMAPI policy helper for ISC DHCP and DDNS so administrators can select the key name, signing algorithm, and omshell path from the site table while preserving the existing xcat_key hmac-md5 default.
Keep local ISC updates from hanging indefinitely when omshell does not exit, and use a static host-declaration fallback for local Ubuntu ISC releases where omshell is unstable for xCAT host updates.
Co-authored-by: gskouson <1507929+gskouson@users.noreply.github.com>
OpenBMC BMCs intermittently return 503 Service Unavailable when the
REST service is busy or recovering. xCAT reported the error immediately,
requiring the user to manually retry. A second attempt usually succeeds.
Retry the same request up to 3 times with a 3-second wait on 503.
If all retries fail, report the error as before. The existing 504
handling for bmcreboot is preserved.
Ref: #4264
Previously, makedhcp warned but still created host entries without
a static IP reservation when a node's address fell inside the
dynamic range. The node would silently get a random IP from the
pool instead of its configured address.
Now errors and skips the node on all four DHCP paths (ISC v4/v6,
Kea v4/v6) with a clear message telling the admin to move the IP
outside the range or adjust the dynamic range.
This makes ISC DHCP and Kea behavior consistent and aligns with
xCAT's design: the dynamic range is for hardware discovery,
known nodes should have static IPs outside it.
Closes#6539